A free, plain language guide to the Erica Synths Syntrx II matrix synthesizer: how the pin matrix works, every module explained, the sequencer and joystick, patch recipes you can try in the browser, settings, MIDI and the best places to keep learning.
What the Syntrx II is, a map of the panel, your first sound in five minutes, every button combination, and what to check when it stays silent.
The Syntrx II is an analog desktop synthesizer from Erica Synths in Latvia, inspired by the EMS Synthi AKS of the early 1970s. Instead of patch cables it has a 16 by 16 grid of lit buttons. Every row is a signal coming out of something (an oscillator, the filter, the joystick). Every column is a place that signal can go (an output, the filter input, an oscillator's pitch). Light a point and the two are connected.
That makes it closer to a small modular synthesizer than a normal keyboard synth. There is no fixed signal path, so it makes no sound at all until you patch one. Once that clicks, it becomes one of the most open ended instruments you can own.
Two stable audio oscillators with waveshaping, plus a third that works as an LFO or reaches into audio range.
256 patch points, each at three strengths, with 256 patch memories that recall the whole grid.
A multimode filter, a looping trapezoid envelope with its own VCA, a ring modulator, noise, sample and hold, delay and reverb.
A recordable joystick, a piano roll sequencer drawn on the matrix, two inputs for outside audio with an envelope follower, and MIDI.
On most synths, sound flows left to right. On the Syntrx II, everything starts and ends at the matrix. A source goes in, the matrix sends it to a module, and the module's output comes back to the matrix as a new row, ready to be sent somewhere else. Patching is going round in circles on purpose.
For the order of the sections, what depends on what, and a seven step way in, see Signal flow.
A simplified layout of the top panel, grouped by section. Positions are approximate; the point is to know which knobs belong together.
| Jack | What it does |
|---|---|
| Power | 12 V DC, centre positive. Use only the supplied adapter; another supply can permanently damage the unit. |
| Output 1, Output 2 | Line level outputs for channel 1 and 2. Panning each channel and sending different things to each gives you stereo. |
| Headphones | Monitor output. |
| Input 1 | Outside audio with the envelope follower. DC coupled. |
| Input 2 | Outside audio with mic or line gain and a polarity invert. DC coupled, so it accepts control voltages too. |
| Scope out | Whatever you send to the Scope column. Normalled to Input 1 and Input 2: with nothing plugged into those inputs, the scope signal appears on them. Great for tricks, surprising when you forget. |
| CV 1 | 1 V per octave pitch for all three oscillators. |
| CV 2 | Takes over oscillator 2's pitch when plugged, for two note (paraphonic) patches. |
| Gate | Fires the trapezoid envelope. Set the trapezoid to non looping first (OFF knob fully clockwise). |
| MIDI in, MIDI thru | Notes, gate, pitch bend, mod wheel, velocity, two assignable CCs and clock. |
Each step below has a button that loads the same patch into the matrix explorer, so you can compare your grid with the diagram.
Syntrx II button combinations. Full guide: sonicdiscoverystudio.com/syntrx-ii
The knob with up and down arrows. Turning it moves the cursor up and down. Pushing it steps the strength of a point: 1, 0.7, 0.3, off.
The knob with left and right arrows. Turning it moves the cursor across. Pushing it connects at full strength, or disconnects.
Videos and forum posts often say "left" and "right"; the manual says "Y" and "X". They mean the same knobs. The last column is what the matrix lights up to show you.
| To do this | Press | The matrix shows |
|---|---|---|
| Everyday patching | ||
| Connect at full strength | Push the right (X) encoder. Push again to disconnect. | Point at full brightness |
| Connect at a lower strength | Push the left (Y) encoder: each push steps 1, 0.7, 0.3, then off. | Point gets dimmer |
| Audition a point without keeping it | Hold SHIFT and hold either encoder. Connected only while held. | |
| Move the cursor with the joystick | Hold SHIFT and move the joystick. Push the right (X) encoder to connect. | |
| Draw points with the joystick | Hold SHIFT and the right (X) encoder, then move the joystick. | |
| Erase points with the joystick | Hold SHIFT and REC/CLEAR, then move the joystick. | |
| Matrix lights off (quieter recordings) | SHIFT + RECALL on the patch screen. Any button brings them back. | Dark matrix |
| Patches | ||
| Save | SAVE, pick a slot with the encoders, push the right (X) encoder. An empty slot saves at once. A slot that already holds a patch asks first: right encoder confirms, left cancels. SAVE or SHIFT backs out. | Slots as a grid or as numbers (P‑VW setting). Over a saved patch: a check mark over the right encoder, a square over the left |
| Recall | RECALL, pick a slot, push either encoder. RECALL again backs out without loading. | Slots as a grid or as numbers |
| Next or previous saved patch | < PATCH · PATCH >. Empty slots are skipped, so it only cycles through the slots that hold a patch. | The patch, not its number |
| Random patch | SHIFT + PATCH >. Turn the volume down first. | A new random grid |
| Delete a saved slot | SAVE, go to the slot, hold SHIFT and push the right (X) encoder. Right confirms, left cancels. | DEL |
| Sequencer screen (open and close with SHIFT + GATE/SEQ) | ||
| Enter a note | Move to the step and note, then push the right (X) encoder: 1 push low octave, 2 middle, 3 high. | Dim, medium, bright |
| Remove a note | SHIFT + push the right (X) encoder. | |
| Gate length of a step | Hold the left (Y) encoder down and turn the right (X) encoder. | Bars in the bottom three rows |
| Last step (sequence length) | SHIFT + turn the right (X) encoder. | |
| Tempo | SHIFT + turn the left (Y) encoder. | The BPM |
| Play direction | Hold < PATCH + turn the right (X) encoder. | FWD, BWD, PP or RND |
| Step by hand | Hold < PATCH + turn the left (Y) encoder to MAN. Each PATCH > press moves one step. | MAN |
| Start · stop | PATCH > | |
| Back to step 1 | SHIFT + PATCH >. | |
| Pitch back to zero while stopped | SHIFT + RECALL. | |
| Stepped modulation lanes | SHIFT + push the left (Y) encoder for the Y lane, push again for the X lane. | Dot bottom left (Y) or bottom right (X) |
| Recording and gates | ||
| Record joystick motion | Hold REC/CLEAR and move the joystick (up to 8 seconds). | |
| Record a gate pattern | Hold REC/CLEAR and press GATE/SEQ in rhythm. | |
| Record effects TIME moves | Hold REC/CLEAR and turn TIME. Not saved with the patch. | |
| Clear a recording | Double tap REC/CLEAR. | |
| Fire the envelope by hand | GATE/SEQ | |
| Settings and power on | ||
| Settings menu | SHIFT + < PATCH. The left (Y) encoder changes page, the right (X) encoder changes the value. | Each setting name scrolls past (SQGL, CLKS, M‑CH…) |
| Leave the settings menu | SHIFT + < PATCH again | Your patch |
| Check the firmware version | In the settings menu, go to FW‑V and push the right (X) encoder | SHOW, then the version, for example 0.05 |
| MIDI panic | Hold SHIFT + REC/CLEAR for 3 seconds. | |
| Firmware update | Hold REC/CLEAR + GATE/SEQ while switching on. | Update screen |
All from the official manual, cross checked against Quincas Moreira's video manual notes. One item to try on your own unit: his notes describe erasing a patch as SHIFT, SAVE and the right encoder pressed together; the manual describes the Delete a slot steps above.
How the sections fit together, which ones depend on which, the order sound travels through them, and a step by step place to start.
The Syntrx II has no fixed path, but almost every patch follows the same order as a classic synthesizer: make a sound, shape its tone, shape its volume, add color and space, send it out.
The matrix is simply the patch cables between those steps. Every arrow in the chart below is one lit point on the grid.
Only the first and last steps are required. You can skip any step in the middle, but you cannot skip the end: nothing is heard until a point is lit in the Ch1 or Ch2 output column.
Everything moving around inside the Syntrx II is one of three things. Knowing which one you are holding tells you where it belongs.
What you actually hear. Oscillators, noise and the two inputs make it. The filter, the trapezoid VCA, the ring modulator and the effects change it. It ends at an output channel.
Slow changing voltages that turn knobs for you. Oscillator 3, the trapezoid, the random section, the joystick and the envelope follower make them. They go to the blue columns: pitch, shape, cutoff, decay and output level.
Gates: simple "now" signals. A key press, the GATE/SEQ button, the sequencer or a drum hit tells the trapezoid when to start. Gates never pass through the matrix.
Think of it as a chain of command. Gates decide when things happen, control decides how settings move, and sound is what gets moved. The knobs set the starting point for each setting; patched control voltages push it up and down from there.
One surprise: the matrix treats sound and control the same way. Any row can go to any column. Send a slow signal into a blue column and a setting sweeps. Send audio into a blue column and the setting moves so fast it changes the tone itself, giving buzzy, metallic, FM style sounds. That is a feature, not a mistake.
The panel splits the matrix into four sections, printed along its edges. Rows are numbered 1 to 16 and columns are lettered A to P, just as on the panel. Here is where each section shows up in the chart.
The things that make a signal: oscillators, noise, the two inputs and the envelope follower.
In the chart: step 1, and the control list under it
Sections that change a signal and send it back to the matrix: filter, trapezoid, ring mod, effects, plus the joystick.
In the chart: the "Out" rows of steps 2 to 4
Where sound goes in: the outputs, the scope and the inputs of each treatment.
In the chart: the "In" columns and the arrows
Where a control signal goes in to move a setting: pitch, shape, decay, cutoff and output level.
In the chart: the boxes on the right
In the chart, the left column is the sound path from top to bottom. The boxes on the right are what can change each step.
Makes the sound. Oscillator 1 (sine and pulse), oscillator 2 (saw and pulse), oscillator 3, noise, Input 1 and Input 2. Each has its own LEVEL knob, and a source with its LEVEL down sends nothing.
Rows 1 to 7 and 9
Pitch from MIDI notes or the CV 1 jack (oscillator 3 only on KEY FOL; CV 2 takes over oscillator 2). Columns H to J bend each oscillator's pitch, column K moves its shape. SYNC locks oscillator 2 to oscillator 1.
Shapes the tone. Removes lows (HPF), highs (LPF) or both. RESONANCE adds a ringing peak. The filter LEVEL knob sets how loud its output is.
In: column G · Out: row 10
Column N moves the cutoff. The switch picks HPF, LPF or both. Classic choices: the trapezoid for a "wow" on every note, oscillator 3 for a slow sweep.
Shapes the volume over time. A volume door that opens and closes, following the trapezoid envelope: ATTACK, ON, DECAY, OFF. SIGNAL sets its output level.
In: column D · Out: row 12
On its own it loops forever. Turn OFF past 9 and it waits for a gate instead (see Timing below). Column L moves the DECAY time.
Ring modulator multiplies two signals for bells and robot voices: A from column E, B from its SOURCE B switch, out on row 13. Effects add delay or reverb: in on column F, out on row 14.
Effects are wet only: send the dry sound to the same output too
Mostly the knobs. TIME motion can be recorded by holding REC/CLEAR. Ring mod needs both A and B, or it stays silent.
Where you hear it. Two channels, each with LEVEL, PAN and a tone control (the output filter), then the Output 1 and 2 jacks and headphones. Column B feeds the scope and its jack.
In: columns A and C
Columns O and P move each channel's volume, for tremolo, ducking and auto panning.
Where the control comes from. These rows feed the blue boxes above:
Use Obsidian? Download this chart as an Obsidian Canvas (10 KB). Drop the file into your vault and it opens as a board you can move around, color and add your own notes to.
Sound and control are patched on the grid. Gates are not: every gate source is combined into a single gate automatically, so any of them can start the envelope.
The rule to remember: looping trapezoid for drones and rhythms on their own, OFF fully clockwise when you play notes. With an outside gate, the length of the gate replaces the ON knob, so holding a key holds the note.
Each step adds one section from the flowchart to the one before. Build each on the hardware, listen, then move on. The buttons load the same patch into the matrix explorer so you can check your grid.
Oscillator 1 pulse straight to Ch1. Learn TUNE, OCTAVE, SHAPE and LEVEL. This is the shortest possible path: step 1 to step 5.
Put the filter in the middle. The output point moves from the oscillator row to the filter row. Sweep LPF and RESONANCE.
Send the filter into the trapezoid VCA, and the VCA to Ch1. It loops on its own, so you hear a pulse. Learn ATTACK, ON, DECAY and OFF.
Your first control patch: oscillator 3 triangle into the Filter freq column at gain 0.7. Set oscillator 3 slow and hear the filter breathe. Nothing new is heard directly; it moves a setting.
Turn the trapezoid OFF fully clockwise. Now it waits. Press GATE/SEQ, play a MIDI keyboard or start the sequencer. Same grid as step 4, new timing.
Send the VCA to the effects as well as to Ch1, and the effects to Ch1. Dry plus wet, mixed by SIGNAL and the effects LEVEL.
Two oscillators into the filter, the whole chain sent to Ch1 and Ch2, with the effects on both. Pan the channels apart. This is the full flowchart in one patch, and a good template to save.
After step 7 you have used every kind of section. From there, the patch recipes are variations on the same chain.
To understand any patch, or find out why it is silent, start at the end. Look at the Ch1 and Ch2 columns and find the lit row. That row is the last section. Look at that section's input column and find what feeds it. Keep going until you reach a source.
If the trail stops before a source, that is the break. The explorer's sound path check does this for you.
Every patch ends with a lit point in the Ch1 Output column (column A). That point always belongs to the row of the last section in the chain. Each time you add a section, the output point moves down to the new section's row.
To switch any point on or off: move the cursor with the encoders (left moves up and down, right moves across), then push the right encoder.
Rows are numbered 1 to 16 down the right side of the panel, and columns are lettered A to P along the bottom.
On Row 1 (Osc 1 pulse) → column A (Ch1)
Output point on row 1. Chain: oscillator → out
Off Row 1 → column A
On Row 1 (Osc 1 pulse) → column G (Filter in)
On Row 10 (Filter out) → column A (Ch1)
Output point moves to row 10. Chain: oscillator → filter → out
Off Row 10 → column A
On Row 10 (Filter out) → column D (Env. signal in)
On Row 12 (Env. signal out) → column A (Ch1)
Output point moves to row 12. Chain: oscillator → filter → VCA → out
Load the three steps one after another in the explorer and watch the lit point in the Ch1 column move down the grid.
If you skip it, the old point stays lit and you hear two versions at once: the plain sound and the processed one, mixed together. With a filter it sounds like the filter is barely working. A leftover point is the most common reason a new section seems to do nothing.
The effects output is wet only, so here you want the dry sound to stay. Keep the old output point lit, send the same row to column F (Effects in), and add row 14 (Effects out) → column A. Now you hear dry plus wet, balanced with SIGNAL and the effects LEVEL.
Hold SHIFT and either encoder on a point to hear it connected only while you hold. Handy for testing a new output point before you switch the old one off.
Most "why is nothing happening" moments come from a section waiting on something else. Each one needs these to work.
| Section | Needs | If missing |
|---|---|---|
| Any sound at all | A lit point in column A or C, from a row that carries sound, and that channel's LEVEL up. | Silence. |
| Each source | Its own LEVEL knob up. Oscillator 1's two waves have separate knobs. | The row is lit but empty. |
| Filter | Something in column G, the filter LEVEL up, and row 10 sent on. | No filter output. |
| Trapezoid VCA | Something in column D, SIGNAL up, and the envelope running: looping, or fired by a gate. | Silent, or one note then nothing. |
| Trapezoid CV | The TRAPEZOID knob up, and the envelope running. | No movement. |
| Ring modulator | Signal A in column E and a signal on SOURCE B, plus its LEVEL. | Silence (anything times zero is zero). |
| Effects | Something in column F and the effects LEVEL up. The dry sound patched to the same output. | Only echoes, or nothing. |
| Random | Something in column M, the OSC3/S&H switch on S&H, and on GATE mode, gates arriving. | Row 5 carries oscillator 3 pulse instead, or holds still. |
| Envelope follower | Audio in Input 1, EF LEVEL turned away from centre, THRESH set so the LED follows the beat, TO GATE on to fire the envelope. | No CV and no gate. |
| Oscillator 3 following notes | KEY FOL selected. | It stays at its own rate. |
| Joystick rows | The X and Y LEVEL knobs up. | Moving it does nothing. |
| Any blue column | Its knob away from the end of its range, so the control voltage has room to move it. | Little or no change. |
What every row and column means, how the three strengths work, and a full size matrix explorer you can click to plan patches, check them and keep your own patch notes.
Each of the 16 rows is a source: a signal leaving a module. Each of the 16 columns is a destination: a place a signal can enter. A lit point connects one to the other. All inputs and outputs are buffered, so you can mix up to 16 rows into one column, or send one row to all 16 columns, without anything getting weaker.
A dot always runs from its row into its column. So a module's row comes before whatever it feeds, and its column comes after whatever feeds it.
The filter has both: row 10 is the sound after the filter, column G is the sound going in.
Ch1 (column A) and Ch2 (column C) have no row, so nothing can come after them. A chain is only heard once it reaches A or C.
Columns H to P carry no sound. A dot there moves a setting for you, so you hear it only when it changes something that already reaches an output.
Every lit dot works at the same time. Recipes light the output first so you hear each step as you build. To trace a patch or find why it's silent, read it backward.
Click a point to cycle it like the left encoder: gain 1, 0.7, 0.3, off. The message box explains each connection, and the status line tells you whether sound can reach an output. Load any recipe from this guide, or build your own and save it in this browser with your knob and switch settings.
The Syntrx II saves the grid but not the knobs, so set them here to match your panel. Drag a knob up or down (or use the arrow keys), or tap the value under it to type a number. Tap a switch position to pick it; tap it again to clear it. Controls you leave alone stay blank, so you can print a blank sheet and fill it in by hand. Above the panel, just like the jacks along the top edge of the unit, tick any that this patch needs a cable in.
On a phone the panel is shown one section at a time. On a computer, or a tablet turned sideways, it appears as the whole panel with every control where it sits on the real Syntrx II.
Saved only in this browser on this device, never sent anywhere. Clearing your browser data erases them, so download a backup file now and then. The same file loads your patches on another phone or computer, or lets you share them with a friend. Print patch sheet gives you a one page paper copy of the grid and every knob and switch.
| Row | Signal |
|---|---|
| 1 · Osc 1 pulse | Pulse wave of oscillator 1. |
| 2 · Osc 1 sine | Sine (shapeable toward a sharkfin) of oscillator 1. Its own row, handy for sending waves to different outputs. |
| 3 · Osc 2 | Pulse and saw of oscillator 2, mixed by their LEVEL knobs. |
| 4 · Osc 3 tri | Triangle to ramp wave of oscillator 3, the main LFO. |
| 5 · Osc 3 pulse / S&H | Either oscillator 3's pulse or the sample and hold output, chosen by the OSC3/S&H switch in the Random section. |
| 6 · Noise | White noise with a tone control. |
| 7 · Input 1 | Outside audio from Input 1 after its LEVEL knob. |
| 8 · Env. follower | A control voltage that follows the loudness of Input 1. Invertible with EF LEVEL. |
| 9 · Input 2 | Outside audio or CV from Input 2, optionally inverted. |
| 10 · Filter | Filter output (or its sine when it self oscillates). |
| 11 · Trapezoid | The envelope as a control voltage, scaled by the TRAPEZOID knob. |
| 12 · Env. signal | Audio coming out of the envelope's VCA, scaled by SIGNAL. |
| 13 · Ring mod | Ring modulator output. |
| 14 · Effects | Delay or reverb output, wet only. |
| 15 · Joystick Y | Vertical joystick voltage, plus MIDI CC Y and the sequencer's Y modulation lane. |
| 16 · Joystick X | Horizontal joystick voltage, plus MIDI CC X and the sequencer's X modulation lane. |
| Column | Destination |
|---|---|
| A · Ch1 Output | Output amplifier for channel 1. |
| B · Scope | The level meter and the Scope out jack, which is normalled to both inputs. |
| C · Ch2 Output | Output amplifier for channel 2. |
| D · Envelope signal | Audio input of the trapezoid's VCA. |
| E · Ringmod A | Signal A of the ring modulator. Signal B comes from the SOURCE B switch. |
| F · Effects | Input of the delay or reverb. |
| G · Filter | Audio input of the filter. |
| H to J · Osc 1, 2, 3 freq | Pitch control for each oscillator. |
| K · Osc shape | Waveshape control for oscillators 1 and 2. The OSC SHAPE switches pick which wave reacts. |
| L · Decay | Control over the trapezoid's decay time. |
| M · S&H input | What the sample and hold samples. Noise gives random steps, a ramp gives staircases. |
| N · Filter freq | Cutoff control. The filter's switch picks high pass, low pass or both. |
| O, P · Output level 1, 2 | Control over each output channel's VCA. Use for tremolo, ducking and auto panning. |
Row and column order follows the connection table in the official manual. If your unit's labels differ, trust the panel.
Every section of the panel in plain language: what it makes, what each control does, where it lives on the matrix, and one thing to try.
Covers roughly C0 to C8. OCTAVE shifts three octaves up or down, TUNE fine tunes over about two octaves. SHAPE changes the pulse width, and bends the sine from pure toward a sharkfin (clockwise) or an inverted sharkfin (counter clockwise). Each wave has its own LEVEL and its own row.
When something is patched into the Osc shape column, the OSC1 SHAPE switch decides what moves: left is pulse width, right is the sine, middle is both. Incoming CV adds to the knob.
Try: send the sine to channel 1 and the pulse to channel 2, pan them apart, and detune slightly with TUNE for a wide drone.
Same range and tuning as oscillator 1. SHAPE changes pulse width and turns the saw from a plain saw (fully counter clockwise) into a dual super saw (fully clockwise). Both waves are mixed by their LEVEL knobs into one row.
The OSC2 SHAPE switch works like oscillator 1's, except the middle position means no CV shaping. The SYNC switch locks oscillator 2 to oscillator 1 for hard sync sounds. Oscillator 2 follows CV 1 unless something is plugged into CV 2.
Try: sync on, then patch the trapezoid into Osc 2 freq for the classic sync sweep.
Runs from 0.05 Hz (one cycle every 20 seconds) up to 500 Hz, so it can be a slow LFO or a low audio oscillator. SHAPE skews the triangle toward a ramp and changes the pulse. FREE runs at its own rate, KEY FOL makes it follow pitch CV like the others.
Its pulse shares row 5 with the sample and hold, picked by the OSC3/S&H switch in the Random section.
Try: triangle into Osc 1 freq at gain 0.3 with a slow rate for vibrato.
Full spectrum white noise from a Zener diode. TONE leans it darker (LOW) or brighter (HIGH). Not voltage controlled. Run it through the filter and the envelope for snares, wind and surf, or feed it to the sample and hold for random voltages.
A high pass and a low pass in series. With LPF fully open (10) you have a high pass on the HPF knob. With HPF fully open (0) you have a low pass on the LPF knob. Anything in between is a band pass whose width you set with the two knobs.
The switch picks which cutoff the Filter freq column moves: HPF, LPF, or both (which moves the band pass centre). With RESONANCE at 7 or more the filter self oscillates into a pure sine you can play like a fourth oscillator. It also takes audio rate modulation for clangy FM style tones.
The Synthi style envelope: ATTACK (6 ms to 0.85 s), ON (hold, up to 1.5 s), DECAY (16 ms to 2 s) and OFF (the pause before it repeats, 14 ms to 1.3 s). By default it loops. Turn OFF past 9 and it stops looping and waits for a gate from the button, MIDI, the Gate jack or the sequencer. With an outside gate, the gate length replaces the ON time.
Two outputs: row 11 is the envelope as CV (depth set by TRAPEZOID), row 12 is the audio that went through its built in VCA (level set by SIGNAL). Decay can be modulated from column L.
Rule of thumb: playing from a keyboard or sequencer, turn OFF fully clockwise. Making drones and rhythms on its own, leave it looping.
Multiplies two signals for metallic, bell like and robotic tones. Signal A comes from the matrix, signal B from the SOURCE B rotary switch. Both must be present. Try two oscillators at unrelated pitches for bells, or a voice on an input against an oscillator for a robot.
Digital effects made with 112dB. The switch picks delay or reverb. TIME is delay time or room size, FEEDBACK sets repeats (it self oscillates when high), LEVEL is the effect volume. Delay range is set to SHORT (up to 0.5 s) or LONG (up to 3 s) in settings, and there are TAPE and BBD flavours.
The output is wet only: send the dry signal to the same output channel too. With reverb feedback mode on and FEEDBACK fully up, the reverb freezes into a loop you can repitch with TIME.
Hold REC/CLEAR and turn TIME to record up to 8 seconds of knob motion. Double tap to clear. This motion is not saved with the patch.
Grabs the level of whatever is in the S&H input column and holds it, making stepped voltages. FREE uses its own clock (S&H RATE), GATE steps once per incoming gate. Set the OSC3/S&H switch to S&H so row 5 carries it.
Noise in gives random steps, oscillator 3's ramp gives staircases. Feed it audio at a high rate for a lo fi bit crush.
Two voltages at once, each up to ±5 V with its own LEVEL knob. MIDI CCs (70 and 71 by default) and the sequencer's two modulation lanes add to the same rows, so one joystick row can carry hand moves, DAW automation and stepped modulation together.
Recording and gate patterns are covered in Sequencer and joystick.
A meter for anything you patch to the Scope column. Use the AUDIO setting to check sounds and the CV setting to watch modulation sources move.
It also feeds the Scope out jack, which is normalled into both inputs. That gives you two extra routes: an extra output, and a way to send a signal back in through Input 2's inverter (the trick behind the auto pan recipe).
The Scope is the meter in the top middle of the panel. It does not show your main output on its own. It only shows what you send to it through column B of the matrix. That makes it a test probe you can point at any part of a patch.
When a patch is silent, check each section along the chain in turn: the oscillator, then the filter, then the VCA. Send each one's row to the Scope column. The first one where the meter stops moving is where the break is.
The quick way: put the cursor on that row's Scope point and hold SHIFT and either encoder. The point is connected only while you hold, so your patch stays exactly as it was.
The matrix mixes everything lit in the same column. Three sources going into the filter at full strength can add up and distort. Send the same rows to the Scope. If the meter is pinned at the top, turn some of those points down to a lower strength with the left encoder.
Set the Scope switch to CV and send oscillator 3 to it. You can watch it swing and set its speed and amount before you patch it to the filter. The same works for the trapezoid, the joystick and the envelope follower: you can see whether they are moving, how far, and in which direction.
Whatever goes to the Scope column also comes out of the Scope out jack on the back. Use it to send one sound to a pedal or a recorder while Outputs 1 and 2 carry the main mix.
It also makes tuning easy: plug a guitar tuner into Scope out, send an oscillator to the Scope column, and tune by eye.
When nothing is plugged into Input 1 or Input 2, the Scope out signal is fed into them automatically. That lets you send a signal back in through Input 2 and flip it with the INVERT switch. This is how the auto pan recipe makes one channel get louder while the other gets quieter.
Watch out: if an input row is lit in your patch with nothing plugged in, whatever you are probing leaks back into the sound. That is the usual cause of surprise noise or feedback.
Treat column B as your test lead. Probe with SHIFT held, do not leave Scope points lit unless you mean to, and clear them before you save, because a saved patch keeps every lit point.
Input 1 brings outside audio onto row 7. Its envelope follower turns that audio into two things: a gate when the signal crosses THRESH (the LED lights), and a CV that follows its loudness on row 8. DECAY smooths the CV. EF LEVEL scales it, and turning it counter clockwise inverts it, which is how you duck the outputs to a kick drum.
The TO GATE switch adds the extracted gate to the other gates, so a drum machine can trigger the trapezoid. It works best on material with clear beats.
LINE or MIC gain (MIC also suits a guitar pickup), LEVEL that can overdrive when turned far up, and DIRECT/INVERT. Being DC coupled, it passes control voltages, so with the invert switch it doubles as a CV inverter fed from the scope.
Two channels, each with LEVEL and PAN (manual only). Each has a VCA: CV patched to Output level 1 or 2 adds to the LEVEL knob, so send a CV to one and its inverted copy to the other for auto panning.
The output filter is a tone tilt: 5 is flat, toward LOW boosts bass, toward HIGH boosts treble.
The piano roll sequencer drawn on the matrix, its two hidden modulation lanes, joystick and gate recording, and recording knob moves on the effects.
Press SHIFT + GATE/SEQ and the matrix turns into a 16 step piano roll. Columns are steps. The top 12 rows are the notes of one octave, with C on the bottom of those 12. Rows 13 to 16 show the sequence length and each step's gate length. The pitch goes to all three oscillators automatically, no patching needed; you still need a patch that makes sound and an envelope that responds to gates.
Example in the style of the manual's diagram: a 12 step sequence starting D, F. Dimmer dots are lower octaves.
| To do this | In the sequencer screen |
|---|---|
| Enter a note | Move with the encoders, then push the right (X) encoder. 1 push low octave (dim), 2 middle, 3 high (full brightness). The range is three octaves. |
| Remove a note | SHIFT + push the right (X) encoder |
| Set the last step | SHIFT + turn the right (X) encoder. Default is 16. |
| Gate length of a step | Hold the left (Y) encoder down and turn the right (X) encoder. Six lengths: 15, 30, 50, 65, 80 and 100 percent (100 ties into the next step). |
| Tempo | SHIFT + turn the left (Y) encoder. The matrix shows the BPM. |
| Play direction | Hold < PATCH + turn the right (X) encoder. The matrix shows FWD, BWD, PP or RND. |
| Step by hand | Hold < PATCH + turn the left (Y) encoder to MAN, then each PATCH > press moves one step. |
| Start · stop | PATCH > |
| Reset to step 1 | SHIFT + PATCH > |
| Pitch back to 0 V when stopped | SHIFT + RECALL |
| Leave the screen | SHIFT + GATE/SEQ |
Saved with the patch. The sequence and both modulation lanes are stored with the current patch. If the sequencer is running when you save, it starts by itself when you recall that patch; stop it before saving if you want to start it by hand.
Clock. Internal or MIDI clock is chosen in settings, along with a MIDI clock division (1, /2, /4, /8). Portamento and a default gate length are settings too.
Inside the sequencer screen, SHIFT + push the left (Y) encoder opens the Y lane (a dot lights bottom left). Push it again for the X lane (dot bottom right). Each lane is a bipolar step pattern drawn as bars, 21 levels per step up to ±5 V, that follows the sequencer's length and direction.
The lanes are added to the joystick rows, so patch Joystick Y or Joystick X anywhere and you get stepped modulation there, scaled by the joystick LEVEL knobs and offset live by moving the stick. Classic uses: a different filter cutoff on every step, an accent pattern on output level, or a second melody on oscillator 2 alone.
Hold REC/CLEAR and move the joystick, up to 8 seconds. It loops half a second after you let go, and the LEDs show the voltages. Move the stick during playback to overdub; playback resumes half a second after you stop. Double tap REC/CLEAR to clear.
Hold REC/CLEAR and tap GATE/SEQ in a rhythm, up to 8 seconds. It loops as a gate pattern for the trapezoid. Double tap REC/CLEAR to clear.
Hold REC/CLEAR and turn the effects TIME knob, up to 8 seconds, for warbling delays and shifting rooms. Double tap to clear. Not saved with the patch.
Gates from the GATE/SEQ button, the sequencer, MIDI notes, the Gate jack and Input 1's follower (TO GATE on) are combined, so any of them can fire the trapezoid.
Patches to build pin by pin, from the first beep to drum processing and sidechain ducking. Every recipe loads into the matrix explorer so you can copy the grid exactly.
How to read these. Each flow shows the pins in order: a source row, a destination column, and the gain if it is not 1. Set the knobs listed under it, start with the outputs low, then adjust by ear. Recipes marked From the manual are the official examples, explained in our words. Idea recipes are built from how the manual says each module works.
The simplest possible patch. Change pitch with TUNE and tone with SHAPE. The manual's version also adds the Osc 1 sine row to Ch1, mixing both waves with their LEVEL knobs.
Your first loop through the matrix: out to the filter, back in on the Filter row, out to channel 1. Sweep LPF, then try HPF and RESONANCE.
Now the trapezoid's VCA controls the volume. With OFF below 9 it loops on its own. Raise SIGNAL to hear it.
Oscillator 3 sweeps the filter, the joystick changes pulse width side to side and pitch up and down. Set the OSC1 SHAPE switch left for pulse width, start with low joystick LEVELs, then record a joystick move.
Pan channel 1 hard left and channel 2 hard right. The scope output is normalled to Input 2, so oscillator 3 arrives there. Set Input 2 to LINE and INVERT: now channel 2 gets louder exactly when channel 1 gets quieter. Adjust depth with the Osc 3 triangle LEVEL and Input 2 LEVEL.
The effects are wet only, so the dry signal and the effect meet at channel 1. SIGNAL sets the dry level, effects LEVEL the wet level.
The computer in a 1970s film. Random section on S&H and FREE, S&H RATE about the same speed as the trapezoid loop, short DECAY. Delay on, moderate feedback, channel 2 panned right.
SOURCE B on oscillator 2. Tune the two oscillators to an odd interval for bells, near unison for slow beating. ATTACK minimum, ON zero, DECAY long. Reverb on, LEVEL low.
Band pass the noise (HPF around 3, LPF around 7), add a little sine for body. Trapezoid OFF fully clockwise, shortest ATTACK, ON at zero, short DECAY. Fire it from the sequencer, MIDI or GATE/SEQ.
SYNC on, oscillator 2 tuned above oscillator 1. Each envelope sweeps oscillator 2's pitch while it stays locked to oscillator 1, giving the tearing sync sound. TRAPEZOID knob sets how far it sweeps.
Low OCTAVE, saw only, filter switch on LPF, RESONANCE around 6. Trapezoid OFF fully clockwise and short DECAY. Draw a sequence with a few 100 percent ties for slides (add portamento in settings), then draw a Y lane for per step cutoff accents.
Reverb with feedback mode on (settings), FEEDBACK high, oscillator 3 very slow. Push FEEDBACK fully up to freeze the room into a loop and play TIME. Two channels panned apart.
These work with any drum machine or loop. A Pērkons HD‑01 is a natural partner; see the Pērkons guide for sending single voices from its outputs.
Filter on LPF with some resonance, cutoff fairly low. Each hit opens the filter. EF LEVEL clockwise, DECAY to taste. Delay with short TIME for a dubby smear. Push Input 1 LEVEL for grit.
The pumping pad. Turn EF LEVEL counter clockwise so the follower is inverted: each kick pulls both output levels down. The kick itself does not pass through the Syntrx; keep it on its own mixer channel and use a split or a separate drum output.
With TO GATE on and OFF fully clockwise, each drum hit above THRESH fires the trapezoid, so the synth plays in time with the drum pattern without any MIDI. Input 1 is not patched to an output, so you only hear the synth.
Saving and organising patches, randomizing, playing from MIDI, every item in the settings menu, calibration and the firmware update.
The whole matrix, the sequence with both modulation lanes, whether the sequencer was running, and the per patch settings (FX mode, reverb feedback, delay length, portamento). The knobs are analog and stay wherever they are, so write them down.
SAVE or RECALL shows the slots on the grid (or as numbers, see Patch view). Pick one with the encoders and push. Press SAVE or SHIFT again to back out without saving, or RECALL again to back out without loading.
Press SAVE, choose the slot and push the right encoder. An empty slot saves straight away. A slot that already holds a patch asks first: a check mark over the right encoder saves, a square over the left cancels. Pick the same number to update a patch, or a new number to keep the original as it was.
The editing screen never shows the slot number, so note it when you recall a patch. Setting P‑VW to NUM makes the save and recall screens show numbers, which is easier to scroll. To peek, press RECALL, then RECALL again to back out. Don't push an encoder while peeking: that reloads the saved copy and drops your unsaved changes.
The current patch is saved every 30 seconds and comes back after a power cycle. Saving to a numbered slot is still the only way to keep it safely.
Press SAVE, go to the slot, hold SHIFT and push the right encoder. DEL appears: right encoder confirms, left cancels.
< PATCH and PATCH > step through saved slots instantly, skipping empty ones. If only a few slots hold patches, they cycle through just those. Save a performance in neighbouring slots and walk through them.
SHIFT + PATCH > makes a random grid. Density (0 to 80 percent) and the area of the grid it may touch are set in the menu. Keep outputs low; some results are silent, some are loud.
Plan your slots. A simple scheme: row 1 for finished sounds, row 2 for sequences, row 3 for input processing, last row for experiments. The patch sheet in the matrix explorer has a field for the slot so your notes and the unit stay in step.
Before playing from MIDI, turn the trapezoid OFF knob fully clockwise. Otherwise the envelope starts looping again every time you release a key.
Open with SHIFT + < PATCH. The left encoder moves between pages (a dot in the far right column shows where you are), the right encoder changes the value. Each page scrolls its name across the top half of the matrix, then settles on the short code in the table below. The bottom half shows the current value. To leave the menu and get back to your patch, press SHIFT + < PATCH again.
| Code | Setting | Options | Scope |
|---|---|---|---|
| FX BD | Effects in BBD mode instead of tape mode | Off, On | Per patch |
| REV F | Reverb feedback instead of tone. At full FEEDBACK the reverb loops what it hears | Off, On | Per patch |
| DELL | Delay length | Short (to 0.5 s), Long (to 3 s) | Per patch |
| P‑TM | Portamento for sequencer and MIDI | 0 to 100 (100 = 1 s) | Per patch |
| SQGL | Default sequencer gate length | 15, 30, 50, 65, 80, 100 % | Global |
| RNDD | Random patch density | 0 to 80 % | Global |
| RNDA | Random patch area: set top left corner, bottom right corner, then move the area | Any rectangle | Global |
| M‑CH | MIDI channel | 0 (omni) to 16 | Global |
| CLKS | Sequencer clock source | INT, MIDI | Global |
| CLKD | MIDI clock division | 1, /2, /4, /8 | Global |
| M‑PB | Pitch bend range | 0 to 12 semitones | Global |
| M‑NO | MIDI note offset to match your keyboard | Up to 3 octaves | Global |
| VELC | Velocity to cutoff depth | 0 to 10 | Global |
| KEYC | Filter key tracking depth | 0 to 10 | Global |
| CC X · CC Y | MIDI CC added to joystick X and Y | Any CC (70, 71 default) | Global |
| P‑VW | How save and recall show slots | MTX grid, NUM numbers | Global |
| CALIB | MIDI pitch calibration (below) | C0 to C8 | Global |
| MX D | Dim the whole matrix | Off, On | Global |
| FW‑V | Shows the firmware version. The bottom half says SHOW: push the right encoder and the version appears, for example 0.05 | Read only | |
| FRST | Factory reset. Deletes all your patches. | Hold right encoder to confirm |
It ships calibrated; recalibrate only if your keyboard plays out of tune across octaves.
Firmware 1.05 (January 2024) fixed a DSP crash after long power on times, made the SHIFT LED light when pressed and improved the joystick. The unit shows it as 0.05; that is the same version. To check yours, open the settings menu, turn the left encoder to the FW‑V page, and push the right encoder when the matrix says SHOW. If it reads 0.05, you are up to date.
Calculate delay and reverb times for any tempo, Syntrx II delay mode, trapezoid loop and oscillator 3 checks, and a note frequency chart. Enter a BPM or tap it in, then click any value to copy it.
Free reference tool from Sonic Discovery Studio, provided as is. Unofficial companion tool, not affiliated with or endorsed by Erica Synths.
The official material, the video lessons worth your time, written reviews with real workflow tips, and where owners talk, plus gear that pairs well. Every link was checked in November 2026.
The best free course: read the manual, watch the Quincas Moreira video manual with the synth in front of you, then rebuild the 50 official patch notes by Gas Of Latvia one at a time. No dedicated paid course for the Syntrx II existed when this guide was written; this combination covers more than one would.
The English manual from May 2023: matrix, modules, sequencer, MIDI and settings.
Andris Indāns made 50 Syntrx II patches with matrix settings and an audio example for each: acid lines, drones, drums, sequences and more.
Printable sheets for the matrix and knob positions. Ten stencils also come in the box.
The current firmware (shows as 0.05 on the unit), with update steps.
Sixteen patches with timestamps in the description.
Specs, the FAQ, all downloads and the support contact.
An 80 minute walk through every section, built up one patch at a time. Jump to a chapter:
What changed from the first Syntrx, a tour of each section and patch ideas, with honest pros and cons.
Using it for real music, compared with the EMS VCS3 and the first Syntrx.
The thinking behind matrix patching, in modular terms.
A complete piece on the Syntrx II alone, then a DB‑01 feeding the matrix.
The features worth exploring first, in a few minutes.
Marcus Schmahl's review reads like a getting started guide: first patch, randomizer, joystick recording, effects on the second output.
Dana Gumbiner on the envelope follower, processing outside sources and the learning curve.
Clear about what it is not: a self contained instrument more than a rack synth.
Written for the first Syntrx, but the matrix ideas carry straight over.
Around 234 posts since May 2022 and still active. The best place for specific questions, bugs and shared patches.
Answers routing and firmware questions directly, and handles repairs and warranty.
A short list of Erica Synths gear that works naturally alongside the Syntrx II.
A four voice drum synthesizer. Set the Syntrx II sequencer's clock source to MIDI and both play in time. Or run its drums into Input 1 and use the envelope follower to fire the trapezoid (recipe O). A free Pērkons guide is on this site too.
A stereo delay unit. Connect Output 1 and Output 2 to its two inputs for a second delay on top of the built in effects, with channel 1 and 2 kept apart in stereo.
A desktop bassline synthesizer with its own sequencer. Sync it over MIDI clock for bass under your Syntrx II patches, or feed it into Input 1 or 2 and run it through the filter, ring modulator and effects.
A small semi modular analog synthesizer designed for learning synthesis. A hands on companion voice, and a gentle way to get comfortable with patching before or alongside the matrix.
As an Amazon Associate I earn from qualifying purchases. Your price stays the same. Affiliate disclosure
Who wrote it, how to get in touch, and the fine print, including the affiliate disclosure.
This is a free, independent guide to the Erica Synths Syntrx II, written to make the instrument easier to learn. It is published by Sonic Discovery Studio, a mixing and mastering studio in Sarasota, Florida, which also publishes a free Pērkons HD‑01 guide. It is built from the official manual (May 2023 edition) and firmware 1.05 notes, published reviews and the experience of owners, and is written in plain language with diagrams.
Found a mistake, or something that works differently on your unit? Corrections and new owner tips are always welcome.
For repairs, warranty and firmware, contact the manufacturer through the Erica Synths support section.
This guide is provided for educational and informational purposes only. It is an independent resource and is not an official Erica Synths publication. Sonic Discovery LLC is not affiliated with, sponsored by or endorsed by Erica Synths.
The information is offered in good faith and as is, without warranties of any kind, whether express or implied, including accuracy, completeness or fitness for a particular purpose. Firmware updates can change how the instrument behaves, and recipes marked as ideas are built from the manual's description of each module rather than published patches. Always check the official manual and Erica Synths support before relying on anything here.
You use this information at your own risk. Sonic Discovery LLC does not assume any liability for loss or damage of any kind arising from the use of this guide, including damage to equipment, lost patches, failed firmware updates, hearing damage from high volume, or any other direct or indirect loss. Keep the volume low when trying new or random patches, note important patches on paper before updating or resetting, and use only the power adapter supplied with the instrument.
Links to other websites are provided for convenience. Sonic Discovery LLC does not control and is not responsible for their content, products or privacy practices.
Erica Synths and Syntrx are trademarks of their respective owners and are used here only to identify the product discussed. All other product and company names are the property of their owners.
This page has no accounts, sign ups or forms, and it does not ask for any personal information.
Saved on your device only. The tab you last viewed, any patches you save in the matrix explorer and your Tempo & Pitch settings are stored in your own browser (local storage). They are never sent to Sonic Discovery. Clearing your browser's site data removes them.
Visitor statistics. Sonic Discovery uses Matomo, a visitor counter that runs on its own server, to see how many people read this guide and which parts are useful. It is set up to work without cookies, and IP addresses are shortened before anything is stored. It also counts how often the patch sheet buttons are used (save, print, backup and so on); only the button is counted, never your patch names or settings, and opening the Tempo & Pitch tab is counted the same way. The information is not sold or shared for advertising.
Hosting and fonts. Like any website, the hosting provider records basic technical information such as your IP address, browser and the pages requested, for security and to keep the site running. The page fonts are loaded from Google Fonts, so Google receives your IP address and browser details when the page loads.
Links to other sites. Amazon, YouTube and other linked sites have their own privacy policies. Amazon may set a cookie when you follow an Amazon link, as explained in the affiliate disclosure below.
Email. If you write to us, your message and email address are used only to reply to you.
This guide is meant for a general audience and is not directed at children under 13. Questions about privacy can be sent to contact@sonicdiscoverystudio.com.
Last updated 7 November 2026.
Sonic Discovery Studio is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. As an Amazon Associate I earn from qualifying purchases.
Your price stays the same, and any commissions help cover the cost of keeping this guide free. Gear is only suggested when it is genuinely useful with the Syntrx II.
When you click an Amazon link, Amazon may place a cookie in your browser so that a qualifying purchase can be credited to this site. Amazon handles that information under its own privacy notice. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.
Last updated 7 November 2026.